Study on the Moment Magnitude of Small and Moderate Earthquakes Located in the Inner Mongolia Region

Based on digital seismic waveform data from Inner Mongolia Digital Seismic Network, the source spectrum parameters of 182 small and moderate earthquakes from January, 2009 to September, 2016 are derived, and the seismic moment M₀ and moment magnitude M_W of the earthquakes are calculated. The M_L-M_W relationship and the relationship between stress drop and magnitude are obtained using the linear regression method. It is clear that incorporating the moment magnitude into the seismic quick report catalog and the official earthquake catalog can enrich earthquake observation report content, thus providing better service for earthquake emergency and earthquake scientific research.     

Fault geometrical model of Dujiangyan section in Longmenshan fault zone

The focal mechanism solution on the seismic fault plane can reflect the geometric and kinematic characteristics of faults, and it is an important way to further study the fine structure of fault plane. From the focal mechanism solution of the earthquakes around the Dujiangyan fault in Longmenshan fault zone, we derived the average dip angle of Dujiangyan fault is 45.1° based on the seismic moment tensor theory. In order to refine the fault geometry structure, this paper decomposed it into multiple sub-fault planes along the length and width of the fault plane and forms a number of models A13, B13, A23 a, A23 b, A23 c, B23 a,B23 b and B23 c, then calculated the sub-fault's dip of each model. In order to clarify exactly which one of the fault models is closest to the real fault model, the fault slip was carried out for each model in turn, then compared the surface displacement of each model with GPS observations. The results show that B23 c model with high dip in shallow and small dip in deep is the best model, the lengths of each subfault of Dujiangyan fault from south to north are 33 km, 21 km and 46 km, respectively. When the depth of the fault bottom is about 11 km, the dip angles are 70.56°, 67.41° and 45.55°.When the depth of the fault bottom is about 30 km, The fault dip angles are 44.55°, 29.18° and 44.25°.     

Full moment tensor inversion constrained by double-couple focal mechanism for induced seismicity*

In this study, we propose a new method to determine full moment tensor solution for induced seismicity. This method generalizes the full waveform matching algorithm we have developed to determine the double-couple (DC) focal mechanism based on the neighbourhood algorithm. One major difference between the new method and the former one is that we adopt a new misfit function to constrain the candidate moment tensor solutions with respect to a reference DC solution in addition to other misfit terms characterizing the waveform matching. Through synthetic tests using a real passive seismic survey geometry, the results show the new constraint can help better recover the DC components of inverted moment tensors. We further investigate how errors in the velocity model and source location affect the moment tensor solution. The synthetic test results indicate that the constrained inversion is robust in recovering both the DC and non-DC components. We also test the proposed method on several real induced events in an oil/gas field in Oman using the same observation system as synthetic tests. While it is found that the full moment tensor solutions without using the DC constraints have much larger non-DC components than solutions with the DC constraints, both solutions are able to fit the observed waveforms at similar levels. The synthetic and real test results suggest the proposed DC constrained inversion method can reliably retrieve full moment tensor solutions for the induced seismicity.     

2013年南斯科舍海岭MW7.8地震的多点震源机制反演

2013年11月17日，在南极南奥克尼群岛北、南极板块与斯科舍板块之间发生了一次M_W7.8级地震（2013年南斯科舍海岭M_W7.8地震），我们利用全球分布的长周期和宽频带地震记录反演确定了这次地震随时间和空间变化的震源机制，验证了提出的一种多点震源机制反演的新方法.首先利用长周期记录的W震相反演了这次地震的矩心矩张量解并利用体波提取了视震源时间函数，同时利用台阵反投影技术从宽频带记录中获得了这次地震的高频源的时空分布，然后基于矩心矩张量解、视震源时间函数以及高频源的时空分布，实现了采用新方法对2013年南斯科舍海岭M_W7.8地震的多点震源机制反演.矩心矩张量解表明，地震矩心在44.50°W/60.18°S，矩心深度19 km，半持续时间49 s，释放标量地震矩4.71×10²⁰ N·m，发震断层走向104°，倾角54°，滑动角8°.视震源时间函数清楚地揭示了地震矩随时间变化的方位依赖性，总体上可以将时间过程分为前60 s和后50 s两个阶段，但前60 s可细分为两次子事件.根据台阵反投影结果，这次地震为沿海沟从西到东的单侧破裂，破裂长度达311 km，可以分为5次子事件，能量释放的峰值点依次为13 s、30 s、51 s、64 s和84 s，平均破裂速度分别为0.6 km·s^-1、2.6 km·s^-1、2.3 km·s^-1、2.8 km·s^-1和3 km·s^-1.多点震源机制反演显示，5次子事件的矩震级分别为M_W7.57，M_W7.48，M_W6.80，M_W7.53和M_W7.08，半持续时间依次为21 s，17 s，6 s，16 s和8 s，走向分别为95°，105°，81°，98°和98°，倾角依次为57°，49°，86°，46°和64°，滑动角-9°，1°，-17°，13°和-4°.这些在震源机制、能量释放以及持续时间方面的变化都是当地构造和应力环境复杂性的反映.     

基于分布式控制力矩陀螺的水下航行器轨迹跟踪控制

基于控制力矩陀螺群(CMGs)的水下航行器具有低速或零速机动的能力。采用基于分布式CMGs的水下航行器方案,并研究其水平面的轨迹跟踪控制问题。通过全局微分同胚变换将非完全对称的动力学模型解耦成标准欠驱动控制模型,并根据简化的模型构建其轨迹跟踪的误差动力学模型,将轨迹跟踪控制问题转化为误差模型镇定问题。基于一种分流神经元模型和反步法设计了系统的轨迹跟踪控制律,该控制器不需要对任何虚拟控制输入进行求导计算,且能确保跟踪误差的最终一致有界性。仿真结果表明该控制器能够实现在不依赖动力学参数先验知识的情况下对光滑轨迹的有效跟踪。     

基于ABAQUS的深水连接器连接性能分析

为解决现有深水连接器连接性能研究中力学分析建模不准确,且缺乏抗弯抗扭能力分析的问题,基于ABAQUS有限元分析软件对深水连接器进行三维模型动态仿真分析,对连接器的受力、密封性能以及在实际工程需求中不同内压下的抗弯及抗扭性能进行深入研究。结果表明:在安装及生产两种工况下,深水连接器各部件除密封环外受力均满足其强度设计要求,密封环接触表面发生合理塑性变形,满足密封要求;随着内压的增加,深水连接器的抗弯能力逐渐下降,抗扭能力则呈现增加的趋势;极限弯矩分别在0 MPa与35 MPa内压下的判定依据为密封失效,在14 MPa与52 MPa内压下的判定依据为下毂座屈服,而极限扭矩在不同内压下的判定依据均为密封失效。     

STUDY ON RELATIONSHIP BETWEEN THE ACTIVITY OF MIYALUO FAULT AND WENCHUAN EARTHQUAKE SEQUENCE

Under the background of thrusting stress regime, a large number of strike-slip earthquakes occurred on the Miyaluo Fault during the Wenchuan earthquake sequence process, which is in the southern part of the Longmenshan Fault. In order to find the cause of their occurrence, stress tensors in subregions near the Miyaluo Fault are estimated. The result shows that in both north and south side of the Miyaluo Fault, the direction of principal compressive stress is nearly perpendicular to the Longmenshan Fault, and its dip is nearly horizontal, and the direction of tensile stress is nearly vertical. While in the Miyaluo fault zone, the direction of principal compressive stress is SWW-NEE, and its dip is nearly horizontal, the direction of principal tensile stress is NNW-SSE, also its dip is nearly horizontal. It is consistent with sinistral shear stress state in the Miyaluo fault zone. It was referred that the behavior of Miyaluo Fault during the Wenchuan earthquake sequence process was caused by tearing effect generated from unbalanced forces of two sides of the fault. To understand the rupture mode of the aftershocks in subregions as described above, the total seismic moment tensors are estimated by adding the corresponding component separately of the seismic moment tensor of aftershocks in each region. The result shows the similar trend of total seismic moment tensor components in the north and south side of the Miyaluo Fault(indicating the consistency of rupture mode in the north and south side of the Miyaluo Fault), and most seismic moment tensor components in the south side is higher than that in the north side, especially the compression component perpendicular to Longmenshan Fault and expansion component in the vertical direction. It indicates that thrusting component in the southeast direction in the south side is greater than that in the north side, and the thrusting difference causes the sinistral tearing effect of the Miyaluo Fault. We also find that the sinistral tearing component of the Miyaluo Fault is the same order of magnitude with the thrusting difference of its two sides, which indicates that the tearing effect of Miyaluo Fault can be completely explained by thrusting difference of its two sides. According to the analysis, we put forward the dynamic model of the Miyaluo Fault, which can explain the above phenomenon.     

Temporal variation of modulated-wave-train geometries and their influence on vertical bending moments of a container ship

A towing experiment was conducted using a modulated wave train to investigate the vertical bending responses of a hydro-structural container ship model. In the experiment, a spatially periodic modulated wave train, as a model of a freak wave in successive high waves mimicking the so-called three sisters, was generated by the recently established higher-order spectral method wave generation (HOSM-WG) method. HOSM-WG enables us to control the location and timing of the maximum crest height in a wave tank. With precise control of the towing carriage, an experiment was conducted in which the timing of the encounters between the ship model and the modulated wave train was accurately determined. The maximum sagging moment (SM) was found to increase in proportion with the encounter wave height. However, because of differences in the relative depth of the fore and aft troughs, the maximum SM is highly variable for a given wave height. The temporal wave-geometry evolution caused the relative trough-depth to vary significantly within a wave period in the vicinity of the maximum crest height. As a result, depending on the encounter timing, the SM varied considerably for a given wave height. The temporal variation of the wave geometry is a robust feature of a modulated wave train and is common between the spatially periodic and temporally periodic modulated wave trains.     

半潜式浮式风机支撑平台首摇运动特性分析

借助FAST软件对OC4半潜式浮式风机平台进行数值计算,分析了影响海上浮式风机平台首摇运动的一系列重要因素及其变化规律(如风向变化、浪向变化、陀螺力矩等)。研究了平台首摇运动所诱导的风机系统动力响应,发现浮式风机首摇运动不仅会加剧平台耦合运动响应,而且还会影响风机的气动性能和加剧锚泊张力波动。提出并探讨了几种减小海上浮式风机支撑平台首摇运动的方法。     

华北地区一次中尺度对流系统上方的Sprite放电现象及其对应的雷达回波和闪电特征

利用低光度相机首次观测到了2013年7月31日华北地区一次中尺度对流系统(MCS)上空产生的中高层Sprite放电现象。结合闪电定位、天气雷达等同步观测, 对一次MCS诱发的Sprite的形态学特征及其对应的母体闪电和雷暴系统的雷达回波特征等进行了详细分析。研究除发现了2例圆柱型、3例胡萝卜型和1例舞蹈型 Sprite外, 还发现了2例发光主体发育不完全的Y字型Sprite。估算的Sprite的底部平均高度低于61.8±3.5 km, 顶部平均高度为84.3±6.8 km。Sprite持续时间算术平均值为25.7±9.8 ms, 几何平均值为24.4 ms。Sprite的母体闪电均为正地闪, 峰值电流在+62.5～+106.2 kA之间, 算术平均值为+77.1±22.2 kA, 是本次MCS所有正地闪平均峰值电流的1.4倍。Sprite母体闪电的脉冲电荷矩变化(iCMC)在+475～+922 C km之间, 几何平均值为+571.0 C km。Sprite母体闪电发生在MCS雷达回波25～35 dBZ的层状云降水区, 弱回波(<30 dBZ)面积的突然增加对Sprite的产生有重要指示作用。Sprite易发生在MCS成熟—消散阶段正地闪比例(POP)显著增加的时段。在本次MCS消散阶段中, 有两个时间段可能有利于产生Sprite。在Sprite集中发生时间段, 北京闪电综合探测网(BLNET)探测到的正地闪比例为54.2%, 正地闪连续电流比例70.24%, 连续电流持续时间为58.17±50.31 ms, 有利于Sprite的产生。